Answer first: On a NSW Class 2 apartment project, any engineer doing professional engineering work in civil, electrical, fire safety, geotechnical, mechanical or structural engineering must be registered under the DBP Act 2020, or directly supervised by someone who is. Registration alone does not let them declare designs. That needs design practitioner registration in the matching class.
By: giantA Pty Ltd · Updated 4 November 2026
Why do professional engineers need their own registration on Class 2 work?
Most developers know that a registered design practitioner must declare regulated designs for a Class 2 building. Fewer realise that the Design and Building Practitioners Act 2020 (DBP Act) also sets up a separate scheme for professional engineers. Under it, the engineer doing the technical work must be registered, even if someone else signs the final declaration.
According to the NSW Government’s professional engineer obligations page, engineers must be registered to do professional engineering work, including giving advice, on regulated buildings. Today those are Class 2, 3 and 9c buildings, plus buildings with a Class 2, 3 or 9c part. Building Commission NSW’s Guidance on Professional Engineering Work (June 2025) adds that on a mixed-use building, the requirement covers work on every part of it, not just the apartment levels. Our guide to mixed-use Class 2 buildings explains how retail, offices and carparks get pulled into the scheme.
Which areas of engineering are prescribed?
The Design and Building Practitioners Regulation 2021 currently prescribes six areas of engineering. Other disciplines, such as mining, chemical, environmental, and IT or telecommunications engineering, are not prescribed at present, so registration is not required for those. The table below matches each prescribed area to the design practitioner class an engineer would need in order to declare designs in that area, using the descriptions on the NSW Government building classes and roles page.
| Prescribed area (professional engineer) | Matching design practitioner class | Typical Class 2 scope | Key exclusion noted by NSW Government |
|---|---|---|---|
| Structural | Design practitioner – structural engineering | Slabs, transfer structures, columns, load-bearing walls, shoring (with geotech) | None listed |
| Civil | Design practitioner – civil engineering | Built-environment civil design connected to the building | Façades, geotechnical engineering and vertical transport integration |
| Geotechnical | Design practitioner – geotechnical engineering | Foundations, retaining structures, shoring excavations, ground bearing | Work involving only geology or earth science |
| Mechanical | Design practitioner – mechanical engineering | HVAC, air distribution, smoke control and exhaust, stair pressurisation | Integration of a vertical transportation product |
| Electrical | Design practitioner – electrical engineering | Electrical services, systems and equipment | Integration of a vertical transportation product |
| Fire safety | Design practitioner – fire safety engineering | Fire performance of materials and structures, fire systems, occupant behaviour in fire, fire prevention, detection and suppression | None listed |
The NSW Government says shoring, underpinning and anchoring need regulated designs from a structural or geotechnical design practitioner. That includes design variations after work starts that may affect them. See our article on Class 2 design variations mid-build.
What counts as “professional engineering work”?
The DBP Act and Regulation define the term, and the Building Commission guidance breaks it into five elements. Work is professional engineering work if it is:
- engineering work in a prescribed area;
- work that requires, or is based on, engineering principles and data;
- applied to an engineering-related design, construction, production, operation or maintenance activity;
- carried out directly in relation to the design or construction of a regulated building; and
- not provided in accordance with a prescriptive standard.
The prescriptive standard exclusion is narrow. It applies only when the work is done purely by following a document that states the procedure or criteria, with no advanced, scientifically based calculations and little or no professional judgement. Once an engineer is making judgement calls, running design calculations or advising on options, the exclusion is unlikely to apply.
The guidance also clarifies what sits outside the scheme. Civil infrastructure that is not part of the building, such as public roads and water mains, is not captured, and neither is work involving only geology. Interstate and overseas engineers are not exempt. If they do professional engineering work on a NSW regulated building, they must be registered here or directly supervised by a registered engineer.
How is a professional engineer different from a design practitioner?
This is the point that trips up most project teams. In the NSW Government’s words, registration as a professional engineer does not on its own allow someone to prepare regulated designs, make design compliance declarations or lodge on the NSW Planning Portal. Those tasks need registration as a design practitioner (or principal design practitioner) in the relevant class.
| Role under the DBP Act | What it lets the person do | Who usually holds it on a Class 2 team |
|---|---|---|
| Registered professional engineer | Carry out professional engineering work (including advice) in the registered area, and directly supervise unregistered engineers | Every engineer doing calculations, design or advice in a prescribed area |
| Registered design practitioner (engineering class) | Prepare or vary regulated designs and make design compliance declarations in that class | The engineer, or a firm signatory, who declares and lodges the engineering designs |
| Principal design practitioner (PDP) | Coordinate the regulated designs and make the principal compliance declaration | Usually the lead architect or registered design practitioner coordinating the team |
According to the design practitioner registration page, an engineer must first be registered as a professional engineer in the matching discipline before registering as a design practitioner in an engineering class. Both can be applied for in the same application. Building Commission guidance also confirms that only the person who declares or lodges needs design practitioner registration. Where a firm makes the compliance declaration on behalf of all the engineers doing the work, each registered professional engineer in that firm does not also need to be a registered design practitioner.
For the wider team picture, see our guide to RDP, building practitioner and PDP roles. For the elements that need declarations, see which building elements need a design compliance declaration.
What about fire safety engineers who are also certifiers?
Building Commission guidance notes that a fire safety engineer registered as a certifier (fire safety, formerly C10) may also need professional engineer registration, and likely design practitioner registration, because a performance solution report can be professional engineering work. Certifier registration does not automatically meet the professional engineer qualification requirements. This ties directly into Class 2 performance solutions and fire engineering reports.
Can an unregistered engineer work on the project under supervision?
Yes, but only under direct supervision by a registered professional engineer in the right area. The Building Commission guidance says the supervising engineer must:
- have direct and ongoing contact with the supervised engineer, not through a third party (remote contact such as video calls, email and phone is allowed);
- make sure the work is within the supervisor’s own registration, authorisation and competence;
- be involved in all stages of the work, with enough control to instruct, oversee and evaluate it; and
- keep evidence of supervision, such as emails, checklists, meeting minutes and design review comments.
The supervising engineer stays responsible for the work. The guidance also states that the DBP Regulation currently contains no authorisations allowing professional engineering work to be done without registration, so supervision is the only route for an unregistered engineer.
What happens if an engineer works unregistered?
Doing professional engineering work in a prescribed area without being registered, supervised or authorised is an offence under the DBP Act. Building Commission NSW’s guidance states that an unregistered engineer could face a maximum penalty of $55,000 or an on-the-spot fine of $5,500, and a supervising engineer who fails to supervise properly risks disciplinary action, including possible cancellation of registration.
There is also a commercial consequence for developers and builders. The guidance says a person who does professional engineering work without being registered, supervised or authorised is not entitled to be paid for it, and any amount paid is recoverable as a debt. If an engineer’s registration lapses mid-project, they are no longer registered to do that work, and the resulting gap can stall a construction certificate or occupation certificate.
What do engineers need to register?
The professional engineer registration page lists the main requirements. Only individuals can register, not companies.
- Aged 18 or over.
- An accepted qualification, such as a four-year bachelor’s or a master’s degree accredited by a Washington Accord signatory, or a degree assessed as equivalent. Fire safety has its own qualification pathways.
- At least five years’ practical experience in the last ten years, including two years in Australia, with relevant experience on Class 2, 3, 9a or 9c buildings.
- A National Police Certificate no older than four months when you apply.
- Meeting the insurance requirements, and not being an undischarged bankrupt.
Engineers registered in Queensland or Victoria can use mutual recognition, but they still need to register in NSW before working on a NSW regulated building.
What ongoing obligations do registered engineers carry?
- Code of practice: comply with the code of practice for professional engineers in the DBP Regulation, including working within their competence.
- CPD: complete 50 hours of relevant education and training per CPD year and keep written evidence.
- Insurance: since 1 July 2022, hold adequate professional indemnity insurance (individual, partnership or corporate policy) and keep checking that it is adequate.
- Records: according to the NSW design obligations page, practitioners, including professional engineers, must keep records for at least 10 years from completion of the building work, even if they stop practising.
How should developers and builders check their engineers?
Here is a practical sequence we use when coordinating engineering consultants on Class 2 projects:
- List every engineering discipline in scope: structural, civil, geotechnical, mechanical, electrical, fire safety, and any facade or vertical transport specialists.
- Check each engineer on the public register using Service NSW’s check the registration of a professional engineer, design practitioner or building practitioner tool. You can search by name, licence number, ABN, ACN or location.
- Confirm who will declare and lodge. Is it the individual engineer, or a firm signatory with design practitioner registration in the matching class?
- Ask about supervision for graduate, interstate or overseas engineers, and request a short supervision statement in the fee proposal.
- Write registration into the consultant agreement: current registration in the right classes, notice of any lapse, PI insurance evidence, and record-keeping.
- Recheck at milestones. Before CC, before each variation and before OC, confirm registrations are still current. See our guides to Class 2 construction certificates and Class 2 occupation certificates.
Are the rules changing in 2026?
Partly. Building Commission NSW announced on 26 June 2026 that applying the DBP Act to remedial work on existing Class 3 and 9c buildings has been deferred to 1 July 2028. The Act continues to apply to alteration, repair and renovation work on existing Class 2 buildings and mixed-use buildings with a Class 2 part. Our Class 2 remedial building work guide covers what that means on site. The same announcement extended the professional indemnity insurance exemption for registered building practitioners to 30 June 2027. That exemption is for building practitioners. The professional engineer obligations page states that insurance has been mandatory for professional engineers since 1 July 2022.
The NSW Government has also said it will not introduce a standalone practice standard for professional engineers and will issue targeted guidance instead. Under the wider Building Productivity Reforms, new legislation is moving through implementation, but the current DBP Act rules continue to apply until changes formally commence. Always check the Building Commission NSW website before you lock in consultant appointments.
Frequently asked questions
Does a structural engineer need to be registered to work on a Class 2 building in NSW?
Yes. Structural engineering is a prescribed area. Anyone doing professional engineering work, including advice, on a Class 2, 3 or 9c building, or a building with such a part, must be registered as a professional engineer or work under the direct supervision of one.
Can a registered professional engineer sign a design compliance declaration?
Not on professional engineer registration alone. Making design compliance declarations and lodging regulated designs requires design practitioner (or principal design practitioner) registration in the relevant class. A firm signatory with that registration can declare on behalf of the firm’s engineers.
Do engineers working on the ground-floor retail of a mixed-use building need registration?
Building Commission guidance says the requirement applies to professional engineering work on all parts of a mixed-use building that has a Class 2, 3 or 9c part. Retail, office and carpark levels in that building are included.
Can an overseas engineering team prepare our structural model?
Only if each engineer doing professional engineering work is registered in NSW or directly supervised by a NSW-registered professional engineer in structural engineering, who stays responsible for the work and keeps supervision records.
How do I check whether an engineer is registered?
Use the Service NSW check tool for professional engineers, design practitioners and building practitioners. Search by name, licence number, ABN, ACN or location, and confirm both the class and the expiry date.
Does professional engineer registration cover Class 1 houses?
No. The DBP scheme currently applies to regulated buildings, meaning Class 2, 3 and 9c buildings and buildings with those parts. Engineers on a standalone house are outside this registration requirement, although other laws and professional standards still apply.
How giantA can help
giantA Pty Ltd is a Sydney architecture and building design practice and a NSW registered design practitioner practice. We coordinate structural, civil, geotechnical, services and fire engineers on Class 2 projects, check registrations and declaration responsibilities, and make sure regulated designs are ready before CC and OC. Explore our Class 2 building design service or get in touch.
Sources
- NSW Government, Professional engineer obligations (last updated 4 November 2025).
- NSW Government, Professional engineer work – qualifications and experience.
- NSW Government, Design practitioner work – qualifications and experience.
- Building Commission NSW, Guidance on Professional Engineering Work (June 2025).
- NSW Government, Building classes and roles under the DBP scheme.
- NSW Government, Design practitioner obligations (last updated 8 September 2026).
- Building Commission NSW, Update on amendments to building regulations (26 June 2026).
- Service NSW, Check the registration of a professional engineer, design practitioner or building practitioner.
- NSW Legislation, Design and Building Practitioners Act 2020 and Design and Building Practitioners Regulation 2021.
This article is general information only and is not legal advice. Check current requirements with Building Commission NSW and your certifier for your project.